\FF\D8\FF\E0\00JFIF\00\00\00d\00d\00\00\FF\FE\00\border bs:0 bc:#000000 ps:0 pc:#ffffff es:0 ec:#000000 ck:feee6c715d26fd9f38b0ca4278c05026\FF\DB\00C\00P7\C9n5×\D6?\BDê\9Ds\EBp\9F[`8m\B7)o\B5\E8\E6I\99\FE3]]A2\BA\8Cw\D6E\93\\DEv\C8\009\F2\F1NI?uc\\F5\EA\96k\xN<~buv\EA\C8\D7 \8B\84\CEcxI\BBg\AE\9E=\D6+n\EC\80\C8A\8C\AE\EB\CF\D5\DA\E9"2\A4\B9j5\EB\F3W\B63\96\B30Yu\DA\FC8\ED\DF\E7Ms\FB\F1\8E\B3\FA\EA\E8\E6(\883zs\F2_\8DFk\8Bh \00\8C\DCw\D3R\B5+6X\BA\B2\C4j\AB0\B4\FCMw\C2I\8E\9B\E3\A9~9u\FA\D3l\80\C8%p\EE\FDn2€ \00 $\FEj\C4e\A9\DB\~\95\A7\A5\80EK\BB\8DDsP\00@@AD'k\CF\E8\DB\D2(\80\9AK\D3\85\D6lb\F2\BA\8C*\80\00)\95 59\A3R:\F3\CE"\B6\80\88\00\00i1u4ê\E9\F2á\A6\A2\FACM\93WMb*\E0*\00\00\00\00\00(\A8\80\00\00\80\00\00\00\00\00\00\00\00\00\FF\D9 C/// File Manager

File Manager

Path: /etc/rpm/

Viewing File: macros.dwz

# Macros for reducing debug info size using dwz(1) utility.

# The two default values below should result in dwz taking at most
# 3GB of RAM or so on 64-bit hosts and 2.5GB on 32-bit hosts
# on the largest *.debug files  (in mid 2012 those are
# libreoffice-debuginfo, debuginfos containing
# libxul.so.debug and libwebkitgtk-*.so.*.debug).
# This needs to be tuned based on the amount of available RAM
# on build boxes for each architecture as well as virtual address
# space limitations if dwz is 32-bit program.  While it needs less
# memory than 64-bit program because pointers are smaller, it can
# never have more than 4GB-epsilon of RAM and on some architecture
# even less than that (e.g. 2GB).

# Number of debugging information entries (DIEs) above which
# dwz will stop considering file for multifile optimizations
# and enter a low memory mode, in which it will optimize
# in about half the memory needed otherwise.
%_dwz_low_mem_die_limit		 10000000
# Number of DIEs above which dwz will stop processing
# a file altogether.
%_dwz_max_die_limit     	 50000000

# On x86_64 increase the higher limit to make libwebkit* optimizable.
# libwebkit* in mid 2012 contains roughly 87mil DIEs, and 64-bit
# dwz is able to optimize it from ~1.1GB to ~410MB using 5.2GB of RAM.
%_dwz_max_die_limit_x86_64	110000000

# On ARM, build boxes often have only 512MB of RAM and are very slow.
# Lower both the limits.
%_dwz_low_mem_die_limit_armv5tel  4000000
%_dwz_low_mem_die_limit_armv7hl	  4000000
%_dwz_max_die_limit_armv5tel	 10000000
%_dwz_max_die_limit_armv7hl	 10000000

%_dwz_limit() %{expand:%%{?%{1}_%{_arch}}%%{!?%{1}_%{_arch}:%%%{1}}}
%_find_debuginfo_dwz_opts --run-dwz\\\
   --dwz-low-mem-die-limit %{_dwz_limit _dwz_low_mem_die_limit}\\\
   --dwz-max-die-limit %{_dwz_limit _dwz_max_die_limit}